About

Fancomkish as an Iranian technology based company is active in field of providing ICT solutions and products for enterprise customers such as Oil & Gas, Bank, etc. Fancomkish is dealing with several most leading ICT global suppliers.

Get In Touch

No.3, 6th alley, sabunchi St., Shahid Beheshti St., Tehran,Iran
Fax: +9821 88536919
Phone: +9821 96861740-5
Postal Code : 1533655513
Home  /  Wifi  /  Indoor Settled Access Points  /  AP5130DN Access Point
FanCom Kish 5-100x100  fancomkish

AP5130DN Access Point

The AP5130DN is a cost-effective 802.11ac access point (AP) that provides a rate of up to 1.75 Gbit/s. It supports rich features and applies to high-density scenarios, including enterprise offices, airports and stations, digital trains, and stadiums, delivering ubiquitous access services.
• 3×3 MIMO (three spatial streams)
• Maximum rate: 1.75 Gbit/s
• External antenna
• 20 dBm

this product was shared 0 times
00
  • توضیحات
  • Characterestic
  • Features

Appearance

 

InterfacesFanCom Kish 265486-1-300x185  fancomkish

FanCom Kish 265486-2  fancomkish

1. Console interface.

2. GE1: a 10/100/1000M interface, which connects to the wired Ethernet.

3. GE0/PoE: a 10/100/1000M interface, which connects to the wired Ethernet and supports PoE power supply.

4. Power input interface: 12 V DC

5. Security slot: connects to a security lock and protects the AP against theft.

6. Default button: restores factory settings if you hold down the button more than 3s.

Highly reliable wireless access

Complies with IEEE 802.11a/b/g/n/ac.
Supports 3 x 3 MIMO and provides a maximum rate of 1.75 Gbit/s.
Supports aggregation of two Ethernet interfaces.
Supports Wi-Fi Multimedia (WMM) and priority mapping on the air interface and wired interface.
Supports wired link integrity check.
Supports load balancing.
Supports roaming without service interruption in Fit AP mode.
Supports AC dual-link backup and VRRP hot backup in Fit AP mode.
Supports 11n Beamforming.
Uses the latest 802.11ac chip to provide higher performance and wider coverage.

Comprehensive user access control capability

Supports access control lists (ACLs) and implements user access control based on the user group policy.
Provides fine-grained bandwidth management for each user.
Supports user isolation policies.
Supports unified authentication on the AC in Fit AP mode.
Identifies the device type according to the organizationally unique identifier (OUI) in the MAC address, user agent (UA) information in an HTTP packet, and DHCP options in Fit AP mode.
The RADIUS server delivers packet forwarding, security, and QoS policies according to the device type carried in the RADIUS authentication and accounting packets in Fit AP mode.

High security

Open system authentication
WEP authentication/encryption
WPA/WPA2-PSK authentication and encryption
WPA/WPA2-802.1x authentication and encryption
TKIP and CCMP encryption for WPA/WPA2/WPA-WPA2: the CCMP uses a 128-bit AES algorithm to encrypt data and has a high security level.
WAPI authentication and encryption
Supports wireless intrusion detection system (WIDS) and wireless intrusion prevention system (WIPS), including rogue device detection and countermeasure, attack detection and dynamic blacklist, STA/AP blacklist and whitelist.

Flexible networking and environment adaptability

Provides flexible networking capabilities and applies to various application scenarios. Mesh and WDS scenarios are supported only in Fit AP mode.
Has strong environment adaptability. The AP can automatically select the transmission rates, channels, and transmit power to adapt to various radio environments and avoid interference in real time.
Adjusts bandwidth allocation based on the user quantity and environment to improve user experience.
Supports the MIMO antenna system and connects to an external dual-band antennas (2.4 GHz and 5 GHz). The antenna direction can be flexibly adjusted.
Identifies interference sources such as Bluetooth devices, microwave ovens, cordless phones, ZigBees, game controllers, 2.4 GHz/5 GHz wireless video and audio devices, and baby monitors in Fit AP mode and works with eSight to locate interference sources and display spectrums.

Simple device management and maintenance

Automatically goes online and loads the configuration, and supports plug-and-play (PnP) in Fit AP mode.
Supports batch upgrade.
Allows real-time monitoring on the network management system (NMS) to facilitate remote configuration and fast fault location.
Supports the Link Layer Discovery Protocol (LLDP) to implement automatic link discovery and obtain the network topology.

WLAN features

Complies with IEEE 802.11a/b/g/n/ac and passed the certification of Wi-Fi Alliance.
Maximum rate: 1.75Gbit/s.
Maximum ratio combining (MRC)
Maximum-likelihood detection (MLD)
Data unit aggregation, including A-MPDU (Tx/Rx) and A-MSDU (Rx only)
802.11 dynamic frequency selection (DFS).
Short GI in 20 MHz, 40 MHz, and 80 MHz modes
Priority mapping and packet scheduling based on a WMM profile to implement priority-based data processing and forwarding
Automatic and manual rate adjustment (the rate is adjusted automatically by default)
WLAN channel management and channel rate adjustment
Automatic channel scanning and interference avoidance
Service set identifier (SSID) hiding
Signal sustain technology (SST)
Unscheduled automatic power save delivery (U-APSD)
Control and Provisioning of Wireless Access Points (CAPWAP) in Fit AP mode
Automatically going online in Fit AP mode
Wireless distribution system (WDS) in Fit AP mode
Mesh networking in Fit AP mode

Network features

Compliance with IEEE 802.3u
Auto-negotiation of the rate and duplex mode and automatic switchover between the Media Dependent Interface (MDI) and Media Dependent Interface Crossover (MDI-X)
SSID-based VLAN assignment
VLAN trunk on uplink Ethernet interfaces
4094 VLAN IDs (1-4094) and a maximum of 16 virtual APs (VAPs) for each radio
AP control channel in tagged and untagged mode
DHCP client, obtaining IP addresses through DHCP
Tunnel data forwarding and direct data forwarding
STA isolation in the same VLAN
Access control lists (ACLs)
Link Layer Discovery Protocol (LLDP)
Uninterrupted service forwarding upon CAPWAP channel disconnection in Fit AP mode
Unified authentication on the AC in Fit AP mode
AC dual-link backup in Fit AP mode
Native IPv6
IPv4/IPv6 dual stack
IPv6 Portal
IPv6 SAVI
IPv4/IPv6 ACL

QoS features

Priority mapping and packet scheduling based on a WMM profile to implement priority-based data processing and forwarding
WMM parameter management for each radio
WMM power saving
Priority mapping for upstream packets and flow-based mapping for downstream packets
Queue mapping and scheduling
User-based bandwidth limiting
Adaptive bandwidth management (the system dynamically adjusts bandwidth based on the number of users and radio environment to improve user experience)
Airtime scheduling
Multi-lane scheduling

Security features

Open system authentication
WEP authentication/encryption
WPA/WPA2-PSK authentication and encryption
WPA/WPA2-802.1x authentication and encryption
WAPI authentication and encryption
Supports wireless intrusion detection system (WIDS) and wireless intrusion prevention system (WIPS), including rogue device detection and countermeasure, attack detection and dynamic blacklist, STA/AP blacklist and whitelist.
DHCP Snooping
DAI(Dynamic ARP Inspection)
IPSG(IP Source Guard)

Maintenance features

Unified management and maintenance on the AC in Fit AP mode
Automatically going online and loading configurations, and plug-and-play (PnP) in Fit AP mode
WDS zero-configuration deployment in Fit AP mode
Mesh network zero-configuration deployment in Fit AP mode
Batch upgrade
Local AP management through the serial interface or using Telnet
Real-time configuration monitoring and fast fault location using the NMS
System status alarm

BYOD

Identifies the device type according to the organizationally unique identifier (OUI) in the MAC address.
Identifies the device type according to the user agent (UA) information in an HTTP packet.
Identifies the device type according to DHCP options.
The RADIUS server delivers packet forwarding, security, and QoS policies according to the device type carried in the RADIUS authentication and accounting packets.

Locating Service

Locates tags manufactured by AeroScout or Ekahau.
Locates Wi-Fi terminals.

Spectrum Analysis

Identifies interference sources such as Bluetooth devices, microwave ovens, cordless phones, ZigBees, game controllers, 2.4 GHz/5 GHz wireless video and audio devices, and baby monitors.
Works with eSight to locate and perform spectrum analysis on interference sources.