About

Fancomkish as an Iranian technology based company is active in field of providing ICT solutions and products for enterprise customers such as Oil & Gas, Bank, etc. Fancomkish is dealing with several most leading ICT global suppliers.

Get In Touch

No.3, 6th alley, sabunchi St., Shahid Beheshti St., Tehran,Iran
Fax: +9821 88536919
Phone: +9821 96861740-5
Postal Code : 1533655513
Home  /  Wifi  /  Indoor Settled Access Points  /  AP5030DN Access Point
FanCom Kish hw_311155-100x100  fancomkish

AP5030DN Access Point

The AP5030DN is a performance-enhanced 802.11ac access point (AP) that provides a rate of up to 1.75 Gbit/s. It is well-designed with rich features and especially applicable to high-density scenarios, including enterprise offices, airports and stations, digital trains, and stadiums, delivering ubiquitous access services.
• 3×3 MIMO (three spatial streams)
• Maximum rate: 1.75 Gbit/s
• Built-in antenna
• 20 dBm

this product was shared 0 times
00
  • توضیحات
  • characteristic
  • Feature
  • Deployment scenarios

Appearance

FanCom Kish 265689-1  fancomkish

Interfaces

FanCom Kish 265689-2  fancomkish

1. Console interface.

2. GE1: a 10/100/1000M interface, which connects to the wired Ethernet.

3. GE0/PoE: a 10/100/1000M interface, which connects to the wired Ethernet and supports PoE power supply.

4. Power input interface: 12 V DC

5. Security slot: connects to a security lock and protects the AP against theft.

6. Default button: restores factory settings if you hold down the button more than 3s.

Information Type
ColorStatusDescription
Default status after power-onGreenSteady onThe AP is just powered on and the software is not started yet.
Software startup statusGreenSteady on after blinking onceAfter the system is reset and starts uploading the software, the indicator blinks green once. Until the software is uploaded and started, the indicator remains steady green.
Running statusGreenBlinking once every 2s (0.5 Hz)1. The system is running properly, the Ethernet connection is normal, and STAs are associated with the AP.
2. The system enters the Uboot CLI.
Blinking once every 5s (0.2 Hz)The system is running properly, the Ethernet connection is normal, and no STA is associated with the AP. The system is in low power consumption state (no data is being transmitted and the EEE function takes effect).
AlarmGreenBlinking once every 0.25s (4 Hz)1. The software is being upgraded.
2. After the software is uploaded and started, the AP working in Fit AP mode enters the registration state and has not registered successfully with the AC yet.
3. The AP registration fails (the CAPWAP link is disconnected).
FaultRedSteady onA fault that affects services has occurred. The fault cannot be automatically rectified and must be rectified manually (the fault can be a DRAM detection failure or system software loading failure).
Blinking once every 0.25s (4 Hz)
A fault that affects services has occurred. The fault cannot be automatically rectified and must be rectified manually (the fault can be an Ethernet interface error, such as a PHY error, or a radio interface detection failure caused by a PCI-e interface error or a baseband chip error).

 

 

Highly reliable wireless access

  • AP5030DN: complies with IEEE 802.11a/b/g/n/ac.
  • Supports 3 x 3 MIMO and provides a maximum rate of 1.75 Gbit/s.
  • Supports aggregation of two Ethernet interfaces.
  • Supports Wi-Fi Multimedia (WMM) and priority mapping on the air interface and wired interface.
  • Supports wired link integrity check.
  • Supports load balancing.
  • Supports roaming without service interruption in Fit AP mode.
  • Supports AC dual-link backup and VRRP hot backup in Fit AP mode.
  • Supports 11n Beamforming.
  • Uses the latest 802.11ac chip to provide higher performance and wider coverage.

 Comprehensive user access control capability

  • Supports access control lists (ACLs) and implements user access control based on the user group policy.
  • Provides fine-grained bandwidth management for each user.
  • Supports user isolation policies.
  • Supports unified authentication on the AC in Fit AP mode.
  • Identifies the device type according to the organizationally unique identifier (OUI) in the MAC address, user agent (UA) information in an HTTP packet, and DHCP options in Fit AP mode.
  • The RADIUS server delivers packet forwarding, security, and QoS policies according to the device type carried in the RADIUS authentication and accounting packets in Fit AP mode.

 High security

  • Open system authentication
  • WEP authentication/encryption
  • WPA/WPA2-PSK authentication and encryption
  • WPA/WPA2-802.1x authentication and encryption
  • WAPI authentication and encryption
  • Supports wireless intrusion detection system (WIDS), including rogue AP and STA detection, attack detection, STA/AP blacklist and whitelist.

 Flexible networking and environment adaptability

  • Provides flexible networking capabilities and applies to various application scenarios. Mesh and WDS scenarios are supported only in Fit AP mode.
  • Has strong environment adaptability. The AP can automatically select the transmission rates, channels, and transmit power to adapt to various radio environments and avoid interference in real time.
  • Adjusts bandwidth allocation based on the user quantity and environment to improve user experience.
  • Identifies interference sources such as bluetooth devices, microwave ovens, cordless phones, ZigBees, game controllers, 2.4 GHz/5 GHz wireless video and audio devices, and baby monitors in Fit AP mode and works with eSight to locate interference sources and display spectrums.

 Simple device management and maintenance

  • Automatically goes online and loads the configuration, and supports plug-and-play (PnP) in Fit AP mode.
  • Supports batch upgrade.
  • Allows real-time monitoring on the network management system (NMS) to facilitate remote configuration and fast fault location.
  • Supports the Link Layer Discovery Protocol (LLDP) to implement automatic link discovery and obtain the network topology.

 

WLAN features

  • Compliance with IEEE 802.11a/b/g/n/ac
  • Maximum rate: 1.75Gbit/s.
  • Maximum ratio combining (MRC)
  • Maximum-likelihood detection (MLD)
  • Data unit aggregation, including A-MPDU (Tx/Rx) and A-MSDU (Rx only)
  • 802.11 dynamic frequency selection (DFS).
  • Short GI in 20 MHz, 40 MHz, and 80 MHz modes
  • Priority mapping and packet scheduling based on a WMM profile to implement priority-based data processing and forwarding
  • Automatic and manual rate adjustment (the rate is adjusted automatically by default)
  • WLAN channel management and channel rate adjustment
  • Automatic channel scanning and interference avoidance
  • Service set identifier (SSID) hiding
  • Signal sustain technology (SST)
  • Unscheduled automatic power save delivery (U-APSD)
  • Control and Provisioning of Wireless Access Points (CAPWAP) in Fit AP mode
  • Automatically going online in Fit AP mode
  • Wireless distribution system (WDS) in Fit AP mode
  • Mesh networking in Fit AP mode

 Network features

  • Compliance with IEEE 802.3u
  • Auto-negotiation of the rate and duplex mode and automatic switchover between the Media Dependent Interface (MDI) and Media Dependent Interface Crossover (MDI-X)
  • SSID-based VLAN assignment
  • VLAN trunk on uplink Ethernet interfaces
  • 4094 VLAN IDs (1-4094) and a maximum of 16 virtual APs (VAPs) for each radio
  • AP control channel in tagged and untagged mode
  • DHCP client, obtaining IP addresses through DHCP
  • Tunnel data forwarding and direct data forwarding
  • STA isolation in the same VLAN
  • Access control lists (ACLs)
  • Link Layer Discovery Protocol (LLDP)
  • Uninterrupted service forwarding upon CAPWAP channel disconnection in Fit AP mode
  • Unified authentication on the AC in Fit AP mode
  • AC dual-link backup and VRRP hot backup in Fit AP mode
  • Native IPv6
  • IPv4/IPv6 dual stack
  • IPv6 Portal
  • IPv6 SAVI
  • IPv4/IPv6 ACL

 QoS features

  • Priority mapping and packet scheduling based on a WMM profile to implement priority-based data processing and forwarding
  • WMM parameter management for each radio
  • WMM power saving
  • Priority mapping for upstream packets and flow-based mapping for downstream packets
  • Queue mapping and scheduling
  • User-based bandwidth limiting
  • Adaptive bandwidth management (the system dynamically adjusts bandwidth based on the number of users and radio environment to improve user experience)
  • Airtime scheduling
  • Multi-lane scheduling

 Security features

  • Open system authentication
  • WEP authentication/encryption
  • WPA/WPA2-PSK authentication and encryption
  • WPA/WPA2-802.1x authentication and encryption
  • WAPI authentication and encryption
  • Supports wireless intrusion detection system (WIDS), including rogue AP and STA detection, attack detection, STA/AP blacklist and whitelist.
  • DHCP Snooping
  • DAI(Dynamic ARP Inspection)
  • IPSG(IP Source Guard)

 Maintenance features

  • Unified management and maintenance on the AC in Fit AP mode
  • Automatically going online and loading configurations, and plug-and-play (PnP) in Fit AP mode
  • WDS zero-configuration deployment in Fit AP mode
  • Mesh network zero-configuration deployment in Fit AP mode
  • Batch upgrade
  • Local AP management through the serial interface or using Telnet
  • Real-time configuration monitoring and fast fault location using the NMS
  • System status alarm

 BYOD

  • Identifies the device type according to the organizationally unique identifier (OUI) in the MAC address.
  • Identifies the device type according to the user agent (UA) information in an HTTP packet.
  • Identifies the device type according to DHCP options.
  • The RADIUS server delivers packet forwarding, security, and QoS policies according to the device type carried in the RADIUS authentication and accounting packets.

 Locating Service

  • Locates tags manufactured by AeroScout or Ekahau.
  • Locates Wi-Fi terminals.

 Spectrum Analysis

  • Identifies interference sources such as Bluetooth devices, microwave ovens, cordless phones, ZigBees, game controllers, 2.4 GHz/5 GHz wireless video and audio devices, and baby monitors.
  • Works with eSight to locate and perform spectrum analysis on interference sources.

The AP5030DN provides 802.11n/ac wireless access networks for places with simple building structure, small size, dense users, and high capacity demands, such as small and medium enterprises and branches.The AP5030DN can be flexibly deployed and works in both Fit AP and bridge mode.

The AP5030DN can work as a Fat AP or Fit AP and switch flexibly between the two working modes based on the network plan.

When the wireless network scale is small, customers need to purchase only AP products and set the APs to work as Fat APs. As the network scale expands, tens of or hundreds of APs exist on the network. To simplify network management, customers are advised to purchase wireless access controllers (ACs) to perform centralized management on the APs and set the APs to work as Fit APs.

Fit AP networking (AP mode):

FanCom Kish 265689-3  fancomkish

In this networking, the AP functions as a Fit AP and provides only data forwarding functions. The AC is responsible for user access, AP going online, AP management, authentication, routing, security, and QoS.

Fit AP networking (WDS mode: point-to-point):

FanCom Kish 265689-4  fancomkish

Fit AP networking (WDS mode: point-to-multipoint):

FanCom Kish 265689-5  fancomkish

In this networking, the AP connects two or more independently wired or wireless LANs through wireless links to construct a network on which users can exchange data. In Wireless Distribution System (WDS) mode, the AP supports point-to-point (P2P) and point-to-multipoint (P2MP) networking modes. With 5 GHz and 2.4 GHz frequency bands, the AP can implement wireless bridging and access functions.

Fit AP mesh networking:

FanCom Kish 265689-6  fancomkish

On the preceding network, APs function as mesh points (MPs) and are fully-meshed to establish an auto-configured and self-healing wireless mesh network (WMN). APs with the gateway function can work as the mesh portal points (MPPs) through which the WMN can provide access to the Internet. Terminals connect to APs to access the WMN. The WMN uses dedicated mesh routing protocols to guarantee high transmission quality and is more applicable to scenarios that require high bandwidth and highly stable Internet connections.

Fat AP networking:

FanCom Kish 265689-7  fancomkish

 

On the preceding network, the device functions as a Fat AP to implement functions such as user access, authentication, data security, service forwarding, and QoS.